The Christmas Big'un.

Post examples...
Of framing styles or techniques that rocked your boat, and also of those that didn't
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

The Christmas Big'un.

Post by prospero »

Frame to fit a 7' x 5' 2" canvas. :D


First step: Make the liner. Rose&Hollis A279. I widened the rebate on my routing table. Big canvases need lots of elbow room.
As it turned out, it was a bit out of square and just fiited. I didn't have the painting on the plot, the guy was still working on it
and no room anyway.....
xmas2018_1.jpg
xmas2018_1.jpg (92.19 KiB) Viewed 9364 times
You will see I had to build extensions to the table to accommodate the thing. I had to commandeer the front of the shop as it was
too big for the workshop. I don't usually like doing 'mucky' work in the shop, hence the dust sheets. I did manage to underpin the liner
but added steel 'L plates ' on the corners.
Watch Out. There's A Humphrey About
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

Stage 2. Build the core of the frame. R&H A138. Once the liner is made the size is set and the important thing to establish
when multi-stacking is the differential between the long and short sides. This is a constant.

I didn't underpin this moulding. I put a biscuit slot in each corner and cross-nailed them. The webbing strap was a must as was
my newly bought spring-clamp set. Very old school. :P

xmas2018_2.jpg
xmas2018_2.jpg (88.73 KiB) Viewed 9363 times
Watch Out. There's A Humphrey About
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

Further corner reinforcement. At this point I had to flip the beast over, which was probably the most problematic thing
of the whole job. :roll:
xmas2018_3.jpg
xmas2018_3.jpg (50.49 KiB) Viewed 9361 times
Watch Out. There's A Humphrey About
poliopete
Posts: 798
Joined: Mon 04 Apr, 2016 7:13 am
Location: The Wash
Organisation: Annie Lou Fine Framing
Interests: Caring for my wife, Picture Framing and Natural History

Re: The Christmas Big'un.

Post by poliopete »

So far so good :clap: :clap:

What device do you use to tighten the webbing?
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

A big spanner. :D
Watch Out. There's A Humphrey About
poliopete
Posts: 798
Joined: Mon 04 Apr, 2016 7:13 am
Location: The Wash
Organisation: Annie Lou Fine Framing
Interests: Caring for my wife, Picture Framing and Natural History

Re: The Christmas Big'un.

Post by poliopete »

I am a little slow at times, but "a big spanner" :?: jes nas compre par :? . Do you mean as a tourniquet or some such?
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

:P

Image

These are brilliant. Unfortunately no longer made. :(
Watch Out. There's A Humphrey About
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

Next.....

A small reeded moulding fitted on the inside. I ran up a section of pine to form a 'bridging' piece under the rebate of the
bigger moulding.

xmas2018_4.jpg
xmas2018_4.jpg (89.16 KiB) Viewed 9293 times
Watch Out. There's A Humphrey About
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

Now the tricky part......

Trying to join an 8' x 6' frame for the outer moulding was a bit too much. So I fixed each rail individually. The corner joints don't
need to be especially strong as the strength of the whole frame is in the middle moulding. Took a bit of faffing about to get the rails the
right length. I assembled the four rails 'dry' with the aid of the spring clamps and the removed one at a time a glued them all the way
along. Nailed though into the middle moulding.

xmas2018_5.jpg
xmas2018_5.jpg (73.03 KiB) Viewed 9289 times
Watch Out. There's A Humphrey About
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

Had to extend the back to swallow most of the depth of the canvas. For this I used a square moulding with the rebate ripped off
and another smaller one with the outer edge chamfered.

The two short sides have a piece of PSE pine glued to the back for the hanging cleats.
xmas2018_6.jpg
xmas2018_6.jpg (71.74 KiB) Viewed 9288 times
Watch Out. There's A Humphrey About
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

The bare frame completed. I added a few small blocks as strengtheners. Getting heavy at this stage. :?
xmas2018_7.jpg
xmas2018_7.jpg (88.66 KiB) Viewed 9286 times
Watch Out. There's A Humphrey About
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

xmas2018_8.jpg
xmas2018_8.jpg (75.51 KiB) Viewed 9285 times
Watch Out. There's A Humphrey About
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

Now to try to flip it over. I couldn't do it on the table as not enough ceiling clearance. So I had to do a three-point turn
on the floor. This had to be done very carefully. Helps if you have arms like a gibbon. :lol:
xmas2018_9.jpg
xmas2018_9.jpg (76.75 KiB) Viewed 9285 times
Watch Out. There's A Humphrey About
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

While the main frame is off the table, time to finish the liner. All 28+ feet of it. :P Six processes, so that like doing one coat
on a piece nearly 180ft long.

Grain filled with polyfilla, two coats of ripple paint to prime and then two coats of 50/50 Titanium White/Buff acrylic.
When dry a toning coat of dilute Raw Umber.
xmas2018_10.jpg
xmas2018_10.jpg (81.26 KiB) Viewed 9284 times
Watch Out. There's A Humphrey About
User avatar
Steve N
Posts: 2992
Joined: Sat 21 Jul, 2007 2:32 pm
Location: Somewhere Staple Hill Bristol
Organisation: Frontier Picture Frames ltd
Interests: Walking our retired Greyhound,art, falling asleep on sofa in front of the telly
Location: Now in Bristol
Contact:

Re: The Christmas Big'un.

Post by Steve N »

Following this, love the step by step technique, well done sir :nod:
Steve CEO GCF (020)
Believed in Time Travel since 2035

Proud to sell Ready Made Frames
http://www.frontierpictureframes.com
http://www.designerpicturemounts.com/
poliopete
Posts: 798
Joined: Mon 04 Apr, 2016 7:13 am
Location: The Wash
Organisation: Annie Lou Fine Framing
Interests: Caring for my wife, Picture Framing and Natural History

Re: The Christmas Big'un.

Post by poliopete »

Absolutely love it :lol: much more entertaining than "Silent Witness"

Hats off to prospero :clap: :clap:

Can't wait for the next installment.
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

(didn't have to wait long Peter. :lol: )

Now for the mucky part.....

Frame is to be black with gold sections. Frame all prepped and any holes filled and sanded.
Building up the black......
xmas2018_11.jpg
xmas2018_11.jpg (58.72 KiB) Viewed 9267 times
Watch Out. There's A Humphrey About
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

All done and surprisingly zero paint on the walls.... :D
xmas2018_12.jpg
xmas2018_12.jpg (87.47 KiB) Viewed 9267 times
Watch Out. There's A Humphrey About
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

The un-gold parts masked off and the parts to be gilded coated with Red Oxide acrylic.
xmas2018_13.jpg
xmas2018_13.jpg (82.75 KiB) Viewed 9265 times
Watch Out. There's A Humphrey About
User avatar
prospero
Posts: 11489
Joined: Tue 05 Jun, 2007 4:16 pm
Location: Lincolnshire

Re: The Christmas Big'un.

Post by prospero »

All the gilding applied. Bronze Powder (2.5 Gold) mixed with varnish.

xmas2018_14.jpg
xmas2018_14.jpg (77.91 KiB) Viewed 9264 times
Watch Out. There's A Humphrey About
Post Reply