hello!
-
- Posts: 7
- Joined: Thu 04 Apr, 2013 5:38 pm
- Location: ireland
- Organisation: mc framing
- Interests: golf
hello!
hi,, i am new to this forum, im irish and have recently taken up picture framing on the side.
i have a problem though , i bought a morso f and it cuts perfectly until i go to join the four sides
together and there are gaps on the inside of each mitre. so it would appear my morso is cutting
mitres at 46ish degrees instead of 45. can someone help me as i am in fear i have bought a dud
i have a problem though , i bought a morso f and it cuts perfectly until i go to join the four sides
together and there are gaps on the inside of each mitre. so it would appear my morso is cutting
mitres at 46ish degrees instead of 45. can someone help me as i am in fear i have bought a dud
-
- Posts: 365
- Joined: Fri 29 Oct, 2010 11:59 pm
- Location: Glasgow
- Organisation: home
- Interests: cars
Re: hello!
Welcome along, It won't be a dud so don't worry about that. Left fence probably needs a slight adjustment.
I think it is , Gap at front=move fence towards you, Gap at back = move fence away from you
It could well be the other way, as it's only something i've read as mine works perfectly
Also how are your blades, sharp?, hollow ground?
There was a good article on Morso servicing on here recently, worth a read if you can find it
I think it is , Gap at front=move fence towards you, Gap at back = move fence away from you
It could well be the other way, as it's only something i've read as mine works perfectly
Also how are your blades, sharp?, hollow ground?
There was a good article on Morso servicing on here recently, worth a read if you can find it
- JohnMcafee
- Posts: 1145
- Joined: Sun 10 Oct, 2010 9:58 am
- Location: Belfast
- Organisation: Scenes
- Interests: Picture Framing
Putting the world to rights - Location: Belfast
- Contact:
Re: hello!
Welcome aboard, Mark.
Rest assured that there is nothing wrong with the geometry of your machine. If you search the forum you will find that this topic has been discussed several times here in the past.
Your problem is caused by movement of the moulding as it is being cut. If you can prevent this movement by tightly holding the moulding on the left hand side as you bring the blade down, particularly on that crucial final cut, you should see a big improvement. On the other hand you could follow the advice of many framers by just compensating for the movement by setting the left fence back towards you a tad. However, note that the amount of correction to be applied in this way depends on the width and hardness of the moulding.
Rest assured that there is nothing wrong with the geometry of your machine. If you search the forum you will find that this topic has been discussed several times here in the past.
Your problem is caused by movement of the moulding as it is being cut. If you can prevent this movement by tightly holding the moulding on the left hand side as you bring the blade down, particularly on that crucial final cut, you should see a big improvement. On the other hand you could follow the advice of many framers by just compensating for the movement by setting the left fence back towards you a tad. However, note that the amount of correction to be applied in this way depends on the width and hardness of the moulding.
"A little learning is a dangerous thing"
(Also known as John, the current forum administrator)
(Also known as John, the current forum administrator)
Re: hello!
Hi and Welcome Mark.
What the last two said.
Wood is funny stuff and it's not exactly consistent. You will probably find this problem gets worse as the blades slowly lose their edge. If you are cutting wideish moulding then the gap will get multiplied because the diverging angle. Use very fine adjustments on the left fence. If you start to get a gap on the outside then you have gone too far.
What the last two said.
Wood is funny stuff and it's not exactly consistent. You will probably find this problem gets worse as the blades slowly lose their edge. If you are cutting wideish moulding then the gap will get multiplied because the diverging angle. Use very fine adjustments on the left fence. If you start to get a gap on the outside then you have gone too far.
Watch Out. There's A Humphrey About
- Jonny2morsos
- Posts: 2231
- Joined: Wed 12 Mar, 2008 10:28 pm
- Location: Lincs
- Organisation: Northborough Framing
- Interests: Fly Fishing, Photography and Real Ale.
- Location: Market Deeping
Re: hello!
You can downlaod the Morso manual here:http://www.lionpic.co.uk/media/242807/m ... list_f.pdf
Section E-3 describes fence adjustment.
Section E-3 describes fence adjustment.
-
- Posts: 7
- Joined: Thu 04 Apr, 2013 5:38 pm
- Location: ireland
- Organisation: mc framing
- Interests: golf
Re: hello!
thanks people. i look forward to trying tomorrow if ye're expert advice works !
-
- Posts: 3
- Joined: Fri 05 Apr, 2013 6:53 am
- Location: West Yorkshire
- Organisation: Names Within Frames
- Interests: Picture Framing
- Location: West Yorkshire
- Contact:
Re: hello!
And a big welcome from a relative newbie too
- Vince442
- Posts: 150
- Joined: Mon 02 May, 2011 11:50 pm
- Location: Macclesfield
- Organisation: Alchemy Art & Framing Ltd
- Interests: Art, photography, architecture, bonsai, travelling
Re: hello!
Hi Mark and welcome!
I was watching an episode of Burn Notice a few weeks back and it had both Sharon Gless and Tyne Daly in it.
I was watching an episode of Burn Notice a few weeks back and it had both Sharon Gless and Tyne Daly in it.
-
- Posts: 7
- Joined: Thu 04 Apr, 2013 5:38 pm
- Location: ireland
- Organisation: mc framing
- Interests: golf
Re: hello!
also.
if i decide to get my blades resharpened , how much would it cost? and where would i get it done, and i would like a good job done, not the shitty ones i have heard so much about. im in limerick in rep of ireland.
if i decide to get my blades resharpened , how much would it cost? and where would i get it done, and i would like a good job done, not the shitty ones i have heard so much about. im in limerick in rep of ireland.
- philipsheldon
- Posts: 278
- Joined: Fri 03 Apr, 2009 3:33 pm
- Location: Nottingham
- Organisation: Ashworth & Thompson Ltd
- Interests: JUDO / NFFC / CRICKET / REAL ALE ...oh, and Life in general.
- Location: Nottingham, England.
- Contact:
Re: hello!
Afternoon,
Welcome the Forum. Ashworth & Thompson offer a blade sharpening service from the Belfast branch.
Let us know if this appeals.
with kind regards,
Phil Sheldon. 00 44 115 964 7507.
Welcome the Forum. Ashworth & Thompson offer a blade sharpening service from the Belfast branch.
Let us know if this appeals.
with kind regards,
Phil Sheldon. 00 44 115 964 7507.
There's nothing I can do if it don't get through, blame it on the Pony Express !
There's nothing I can say if it's gone a stray, blame it on the Pony Express !
There's nothing I can say if it's gone a stray, blame it on the Pony Express !
-
- Posts: 7
- Joined: Thu 04 Apr, 2013 5:38 pm
- Location: ireland
- Organisation: mc framing
- Interests: golf
Re: hello!
i appreciate your help regarding getting my blades sharpened, but as i am down the south of ireland would i not be a bit far away from ye?
regards
mark
regards
mark
Re: hello!
Post them. Maybe costs a bit in postage, but that's life.
If you deal with A&T then maybe the rep could visit and take back the blunt blades.
Beware general sharpening services. It's not worth saving a few yoyos. Morso blades need specialist sharpening.
If you deal with A&T then maybe the rep could visit and take back the blunt blades.
Beware general sharpening services. It's not worth saving a few yoyos. Morso blades need specialist sharpening.
Watch Out. There's A Humphrey About
Re: hello!
i get mine sharpened by amd in dublin, they send them to a place in dublin who specialise in it
and amd just collect them and drop them back, might cost a little more but no grief
and amd just collect them and drop them back, might cost a little more but no grief
-
- Posts: 7
- Joined: Thu 04 Apr, 2013 5:38 pm
- Location: ireland
- Organisation: mc framing
- Interests: golf
Re: hello!
cool thanks guys. might try amd first so as they are nearer.