Page 1 of 1

New Member Intro

Posted: Mon 11 Feb, 2019 1:36 am
by Sydtheframer
Hello ...I am a new member ... I am Syd Conisbee ... AKA Syd the framer ... Hence my aol email address... From London England ... Now living in the USA ... My business premises were in Connaught Street ... Next to Hyde Park ... London ... England... When I sold my business I retained the picture stock which is over 2000 prints pre dating 1880 ... Just lately I have acquired second hand ... A Morso Cutter... A Seal Dry Mount Press ... A Fletcher Terry Glass/Media Cutter ... A C& H Mat Cutter ... A Brevetti V Nailer (under Pinner) ... Plus lots of odds and end throw in with these used purchases ... So I'm in the midst of setting up my framing workshop ... I specialized in Mount decoration ... Wash lining and french mats ... Many thing are different here so I expect I will have questions ... Pleased to meet you all ..

Re: New Member Intro

Posted: Mon 11 Feb, 2019 7:46 am
by poliopete
Hello Syd and welcome to the FF :D

I read your intro' on the Gumble and was looking forward to meeting you here :P

It sounds like you have a very efficient set up in your new base and I wish you all the very best.

Like all framers we have lots in common and like you I have a passion for not only framing, but mount decoration :rock:

Peter.

Re: New Member Intro

Posted: Mon 11 Feb, 2019 10:59 pm
by Sydtheframer
Thank you Peter

Re: New Member Intro

Posted: Tue 12 Feb, 2019 9:46 am
by David McCormack
Welcome to the forum :handshake:

Re: New Member Intro

Posted: Tue 12 Feb, 2019 9:52 am
by cleaver
Welcome, Syd....I hope this place feels like a little bit of Blighty!! :D :beer:

Re: New Member Intro

Posted: Tue 12 Feb, 2019 1:17 pm
by Sydtheframer
Thank you all for the welcome

Re: New Member Intro

Posted: Tue 12 Feb, 2019 4:48 pm
by John Ranes II, CPF, GCF
Welcome Syd,

So where in North Carolina - US are you setting up business? Storefront or home-based?

Regards,

John

Re: New Member Intro

Posted: Tue 12 Feb, 2019 4:58 pm
by poliopete
Hello, again Syd :D

I just wanted to say you must visit South Carolina if you haven't already, specifically Hilton Head Island, it's absolutely stunning. My wife and I had the holiday of a lifetime there a few years ago.

Peter.

Re: New Member Intro

Posted: Tue 12 Feb, 2019 5:40 pm
by Sydtheframer
cleaver wrote:Welcome, Syd....I hope this place feels like a little bit of Blighty!! :D :beer:


i like it here ... Im not going back ... This Home and I.m now a citizen ...

Re: New Member Intro

Posted: Tue 12 Feb, 2019 5:42 pm
by Sydtheframer
John Ranes II, CPF, GCF wrote:Welcome Syd,

So where in North Carolina - US are you setting up business? Storefront or home-based?

Regards,

John
John Im in Winston Salem ... At the moment I will be home based till I get set up and sorted out ... Then we will see ...

Re: New Member Intro

Posted: Tue 12 Feb, 2019 5:43 pm
by Sydtheframer
David McCormack wrote:Welcome to the forum :handshake:
Thank you David

Re: New Member Intro

Posted: Tue 12 Feb, 2019 5:43 pm
by Sydtheframer
poliopete wrote:Hello Syd and welcome to the FF :D

I read your intro' on the Gumble and was looking forward to meeting you here :P

It sounds like you have a very efficient set up in your new base and I wish you all the very best.

Like all framers we have lots in common and like you I have a passion for not only framing, but mount decoration :rock:

Peter.
Thank you Peter

Re: New Member Intro

Posted: Tue 12 Feb, 2019 5:44 pm
by Sydtheframer
David McCormack wrote:Welcome to the forum :handshake:
Thank you David ...

Re: New Member Intro

Posted: Tue 12 Feb, 2019 5:45 pm
by Sydtheframer
poliopete wrote:Hello, again Syd :D

I just wanted to say you must visit South Carolina if you haven't already, specifically Hilton Head Island, it's absolutely stunning. My wife and I had the holiday of a lifetime there a few years ago.

Peter.
I will as soon as I can