Hello,
I have two pieces of artwork, low value prints produced by an inkjet printer I guess (material is possibly PU? see picture).
Client is a pub owner who uses this purely as decoration, so we are not talking conservation here. He wants an acrylic glass in front to avoid any breakage issue.
The pictures (600x700mm) were both mounted with glue on foamboard that warped quite a bit. I was able to take the print off the foamboards easily.
Question is, what would you mount these prints on ?
I am not used to this type of prints. I normally make frames for paper artwork on a normal mount with T hinges and I use Art bak and Sekisui tape to protect the back.
What would you use to mount the prints on? Nubord? MDF ? Something else?
Thank you
Mounting a colour print on - which board?
-
Starboard
- Posts: 27
- Joined: Tue 24 Dec, 2024 3:37 pm
- Location: SW London-Surrey
- Organisation: BabelOn-line
- Interests: Photography, hopefully framing, and i make mean cocktails
Mounting a colour print on - which board?
You do not have the required permissions to view the files attached to this post.
-
Justintime
- Posts: 2567
- Joined: Sat 26 Sep, 2015 8:48 am
- Location: West Wales
- Organisation: George The Framer LLP
- Interests: Gardening, design, electronic music, good food and beverages.
- Contact:
Re: Mounting a colour print on - which board?
It does look plastic, it looks like a "print on canvas'. If it was me I'd first ask my supplier what self adhesive board they'd recommend for a plastic canvas print. Next I'd approach my local sign/banner maker graphics business. They'll have the materials and experience to do it, but in my experience the cost is surprisingly high but they use proper quality display board.
Alternatively if there's any/enough border left on the print, it could be stretched over strainer bars and glazed.
If it peeled right off the foam board it was probably mounted with spray mount which never gives a permanent adhesion.
Alternatively if there's any/enough border left on the print, it could be stretched over strainer bars and glazed.
If it peeled right off the foam board it was probably mounted with spray mount which never gives a permanent adhesion.
Justin George GCF(APF)
- Tudor Rose
- Posts: 1263
- Joined: Wed 10 Mar, 2010 4:07 pm
- Location: Dawlish, South Devon
- Organisation: The Framing Lot
- Interests: Tudor history, swimming, walking and needlework.
- Contact:
Re: Mounting a colour print on - which board?
Wet mount it to 2.4mm or 3.5mm level 2 board. Prime the board first. Use EVA-CON R or starch paste for the wet mounting.
Jo Palmer GCF(APF) Adv
Adv Textile, Adv Mount Design & Function & Adv Conservation
Forum Moderator & Industry Educator
Guild Certified Examiner & Guild Accredited Trainer
Guild Chair & Master 2019-2022
Adv Textile, Adv Mount Design & Function & Adv Conservation
Forum Moderator & Industry Educator
Guild Certified Examiner & Guild Accredited Trainer
Guild Chair & Master 2019-2022
- Steve Goodall
- Posts: 843
- Joined: Thu 08 May, 2008 4:22 pm
- Location: Up North
- Organisation: Happily Retired - working for beer now
- Interests: Gothic Punk / Man City / Photography...
Re: Mounting a colour print on - which board?
Get a sanding block and sand the back of the print. Then wipe it to remove all the dust of course. Now it should stick down quite easily onto virtually anything. If you are going to use foamboard again I would look for something with an aggressive adhesive. Forget anything that says "repositionable" or "reversible". That simply means the adhesive is a waste of time.
Your too late I'm afraid - I retired in April 2024 
