Framing medals - correct method of attaching ribbons

Discuss Picture Framing topics.

PLEASE USE THE HELP SECTION
WHEN SEEKING OR OFFERING HELP!
Post Reply
Not your average framer
Posts: 11008
Joined: Sat 25 Mar, 2006 8:40 pm
Location: Devon, U.K.
Organisation: The Dartmoor Gallery
Interests: Lost causes, saving and restoring old things, learning something every day
Location: Glorious Devon

Framing medals - correct method of attaching ribbons

Post by Not your average framer »

Hi,

I've been thinking of doing a medals case display in the shop window using replica medals. These replica medals come supplied with 6 inches of ribbon which you have fit yourself.

Can anyone give any advice about the correct way to do this in particular:

1. The correct length of ribbon to be showing.

2. How to attach if the medal only comes with a small round ring to attach the ribbon to. I've seen medals with the ribbon folded and fitted through the ring, but can't remember how it was done.

3. Should the ribbon always be attached to a broach-bar at the top?, or if it is only for framing, (i.e. not to be worn), is it customary to omit the broach-bar?

Thanks,
Mark
User avatar
Merlin
Posts: 1540
Joined: Thu 05 Jun, 2003 5:50 pm
Location: Cornwall
Organisation: Merlin Mounts
Interests: Aviation

Post by Merlin »

Hi Mark
I have completed quite a few Military medal display boxes.

To me there is a difference between a Military/Campaign medal and other awards like sports or achievements.

To try and answer your questions though.
1. I always mount military medals on a brooch bar. This way they can be easily taken out for cleaning or for wearing and then replaced.
2. From the top of the ribbon to the bottom of the medal should measure 95mm.
3. Where a ribbon enters a closed ring then the folds should be 45 degs either side. This takes a bit of careful folding and very careful use of a steam iron and pressing cloth.
4. There are 2 ways to mount medals a) Swing Mount - where they can swing freely but also lay flat. The normal way. b) Court Mount - where they are sewn onto a backing type plate with the same ribbon as a backing. Normally for Royalty or for High Ceremonial occassions.
5. Please make sure that the order of precedence is correct.
See the following link for that
http://www.medals.org.uk/united-kingdom ... ibbons.htm

Hope that helps you.
John GCF
Not your average framer
Posts: 11008
Joined: Sat 25 Mar, 2006 8:40 pm
Location: Devon, U.K.
Organisation: The Dartmoor Gallery
Interests: Lost causes, saving and restoring old things, learning something every day
Location: Glorious Devon

Post by Not your average framer »

John,

Thanks for the info - Most helpful.
Mark
Not your average framer
Posts: 11008
Joined: Sat 25 Mar, 2006 8:40 pm
Location: Devon, U.K.
Organisation: The Dartmoor Gallery
Interests: Lost causes, saving and restoring old things, learning something every day
Location: Glorious Devon

Post by Not your average framer »

John,

I assume that medal ribbons are made to a standard width. Any chance of telling me what that might be?
Thanks,
Mark
User avatar
Merlin
Posts: 1540
Joined: Thu 05 Jun, 2003 5:50 pm
Location: Cornwall
Organisation: Merlin Mounts
Interests: Aviation

Post by Merlin »

Mark
Not all ribbons are the same width unfortunately..
They are supposed to be 32mm wide as the standard. I have one that is 34mm wide yet others that are 33mm.

I would work on 32mm if you want to make 'slits' in the mount instead of using a brooch.
John GCF
Not your average framer
Posts: 11008
Joined: Sat 25 Mar, 2006 8:40 pm
Location: Devon, U.K.
Organisation: The Dartmoor Gallery
Interests: Lost causes, saving and restoring old things, learning something every day
Location: Glorious Devon

Post by Not your average framer »

Thanks John,

No, it's not for making slits in the mountboard, but for helping me make a spreadsheet for medal case dimensions and prices.

I am gradually coming up with spreadsheets and worksheets for every task we are likely to undertake. In the longer term, it will enable me to delegate more of the work to my staff, both in the workshop and when serving customers.
Post Reply