Trucut Mount Cutter - DXF - ODF file converter needed

Upload/download patterns, templates, designs.
Post Reply
Oculus
Posts: 15
Joined: Mon 10 Oct, 2016 10:27 am
Location: Warrington, Cheshire
Organisation: Oculus Studios
Interests: Photography, mounting, framing

Trucut Mount Cutter - DXF - ODF file converter needed

Post by Oculus » Tue 23 May, 2017 9:50 am

I have a pretty old Trucut mount cutting machine running on Windows 95.
The software converts DXF files to ODF files so that the machine can make the cut.
I have had DXF files made out of shapes I provide, but when I try to convert these DXF files to ODF, I get a "General protection fault" when trying to load the ODF file.

Is there anyone on the forum who can provide the ODF file from a jpg/bmp/png file?
Alternatively, does anyone have a solution to the fault I'm getting?

User avatar
JohnMcafee
Posts: 1090
Joined: Sun 10 Oct, 2010 9:58 am
Location: Belfast
Organisation: Scenes
Interests: Picture Framing
Putting the world to rights
Location: Belfast
Contact:

Re: Trucut Mount Cutter - DXF - ODF file converter needed

Post by JohnMcafee » Wed 24 May, 2017 10:59 am

If you send me the DXF file, I'll see if I can convert.
"A little learning is a dangerous thing"

(Also known as John, the current forum administrator)

Oculus
Posts: 15
Joined: Mon 10 Oct, 2016 10:27 am
Location: Warrington, Cheshire
Organisation: Oculus Studios
Interests: Photography, mounting, framing

Re: Trucut Mount Cutter - DXF - ODF file converter needed

Post by Oculus » Wed 24 May, 2017 11:50 am

Do you have an email address to send the DXF file to John?

User avatar
JohnMcafee
Posts: 1090
Joined: Sun 10 Oct, 2010 9:58 am
Location: Belfast
Organisation: Scenes
Interests: Picture Framing
Putting the world to rights
Location: Belfast
Contact:

Re: Trucut Mount Cutter - DXF - ODF file converter needed

Post by JohnMcafee » Wed 24 May, 2017 12:04 pm

PM sent
"A little learning is a dangerous thing"

(Also known as John, the current forum administrator)

User avatar
JohnMcafee
Posts: 1090
Joined: Sun 10 Oct, 2010 9:58 am
Location: Belfast
Organisation: Scenes
Interests: Picture Framing
Putting the world to rights
Location: Belfast
Contact:

Re: Trucut Mount Cutter - DXF - ODF file converter needed

Post by JohnMcafee » Sun 28 May, 2017 9:35 am

Plane image
planeSmall.gif
After tracing and exporting in CorelDRAW!
[Click to download]
plane.dxf
Converted DXF to ODV in Trucut application
[Click to download]
PLANE.ODF
You do not have the required permissions to view the files attached to this post.
"A little learning is a dangerous thing"

(Also known as John, the current forum administrator)

User avatar
Steve N
Posts: 2478
Joined: Sat 21 Jul, 2007 2:32 pm
Location: Bath, in the wild wild west
Organisation: Frontier Picture Frames
Interests: Walking our retired Greyhond,art, falling asleep on sofa in front of the telly
Location: Bath, Somerset
Contact:

Re: Trucut Mount Cutter - DXF - ODF file converter needed

Post by Steve N » Mon 29 May, 2017 1:59 pm

Very much like one of the designs we cut for a client of ours
Steve CEO GCF (020)
Believed in Time Travel since 2035

Proud to sell Ready Made Frames
http://www.frontierpictureframes.com
http://www.designerpicturemounts.com/

Post Reply